November 16, 2026
M15 concrete mix design as per IS 10262:2019 showing a 100 mm target slump initial trial mix for mild-exposure plain concrete
M15 concrete mix design as per IS 10262:2019 for a 100 mm target slump—an initial trial mix for mild-exposure plain concrete.

M15 Concrete Mix Design as per IS 10262:2019

This page presents an illustrative M15 concrete mix design using OPC 53 cement, 20 mm crushed coarse aggregate, M-sand and a superplasticizer for a 100 mm target slump.

The calculations follow the general mix-proportioning approach of IS 10262:2019. The final mix must be confirmed through laboratory and site trials using the actual cement, aggregates, water, admixture, batching system and project requirements.

Important: This is an initial trial mix for mild-exposure plain concrete. It is not a universal M15 concrete recipe. Final production quantities must be approved after trial-mix testing.

Page Contents

Mix Stipulations

PropertyAdopted value
Grade of concreteM15
Characteristic compressive strength at 28 days15 N/mm²
CementOPC 53 grade
Mineral admixtureNone
Maximum nominal size of aggregate20 mm
Target slump100 mm
Exposure conditionMild exposure for plain concrete
Concrete placementNormal, non-pumped placement
Degree of supervisionGood
Coarse aggregateCrushed angular aggregate
Fine aggregateM-sand/crushed stone sand, assumed Zone II
Chemical admixtureSuperplasticizer
Adopted water–cement ratioApproximately 0.55
Adopted cement content250 kg/m³
Design basisAggregates considered at saturated surface-dry condition

Important Exposure and Grade Note

For reinforced concrete in mild exposure, the minimum grade requirement is M20. Therefore, this M15 example is intended only for plain or non-structural concrete applications.

This example is prepared for plain concrete only.

M15 concrete may be considered for:

  • Levelling concrete
  • Blinding concrete
  • Bedding concrete
  • Plain concrete below foundations, where permitted
  • Other non-structural concrete works

M15 should not be used as a general grade for reinforced concrete. The minimum RCC grade depends on the exposure condition and project specification.

For the selected mild-exposure plain-concrete condition, the applicable reference values are:

Maximum free water–cement ratio: 0.60
Minimum cement content: 200 kg/m³

These are durability reference limits for mild-exposure plain concrete. They do not by themselves determine the final cement content.

Material Properties

Cement and Admixture

MaterialPropertyAdopted value
CementTypeOPC 53 grade
CementSpecific gravity3.15
SuperplasticizerTypeHigh-range water-reducing admixture
SuperplasticizerSpecific gravity1.09
Superplasticizer dosagePercentage by mass of cement0.60%

The actual admixture dosage must be checked against the manufacturer’s technical datasheet and trial results.

Aggregate Specific Gravity

AggregateSpecific gravity
20 mm coarse aggregate2.70
12.5 mm coarse aggregate2.70
M-sand/crushed stone sand2.65
Water1.00

The specific gravity values used here are assumed values. Actual laboratory test results must be used for final mix approval.

Aggregate Moisture Condition

The main calculation is based on saturated surface-dry aggregate conditions.

Actual field batching requires correction for:

  • Aggregate absorption
  • Free surface moisture
  • Stockpile condition
  • Rainfall or drying
  • Batch-plant weighing procedure

Target Mean Strength

The characteristic compressive strength of M15 concrete is:

fck = 15 N/mm²

When sufficient test data are not available, the assumed standard deviation for M15 may be taken as:

S = 3.5 N/mm²

For M10 and M15 grades, the value of X is:

X = 5.0 N/mm²

The target mean strength is calculated using both expressions.

3.1 Calculation Using Standard Deviation

f′ck = fck + 1.65S

f′ck = 15 + (1.65 × 3.5)

f′ck = 20.78 N/mm²

Calculation Using Grade-Dependent Margin

f′ck = fck + X

f′ck = 15 + 5

f′ck = 20 N/mm²

The higher value is adopted:

Target mean strength = 20.8 N/mm²

The actual standard deviation should be calculated from project test results whenever sufficient records are available.

Selection of Water–Cement Ratio

The preliminary water–cement ratio adopted for this example is:

Adopted w/c = 0.55

The selected water–cement ratio must satisfy:

  • Required target strength
  • Durability requirements
  • Workability requirement
  • Project specifications
  • Trial-mix results

The value of 0.55 is an initial trial value for the selected mild-exposure plain-concrete condition. It is not a universal water–cement ratio for every M15 concrete mix.

Water Content Calculation

For 20 mm angular aggregate and a reference slump of 25–50 mm, the approximate water content is:

Water content = 186 litres/m³

The required target slump is 100 mm.

The increase above the reference slump range is approximately 50 mm. Using an approximate 3% increase for every 25 mm increase:

Water increase = 6%

Water Before Admixture Reduction

Water = 186 × 1.06

Water = 197.16 litres/m³

Therefore:

Water before admixture reduction ≈ 197 litres/m³

Water Reduction Using Superplasticizer

For this illustrative calculation, a 30% water reduction is assumed based on the use of a superplasticizer.

This 30% reduction is not a fixed code value. It must be confirmed by trial mixing using the actual cement, aggregates and admixture.

Reduced water = 197.16 × 0.70

Reduced water = 138.01 litres/m³

Adopted external design water

External design water = 138 litres/m³

Water-Balance Note for Liquid Admixture

For this illustrative calculation, 138 litres/m³ is treated as the externally added design water. The liquid superplasticizer is included separately by its full mass and volume. Its water contribution is not included in the 138 litres/m³ figure because the manufacturer’s product water content has not been specified.

Therefore, the calculated water–cement ratio of 138 ÷ 250 = 0.552 is based on the adopted external-water calculation. For an approved final mix, obtain the admixture water content from the manufacturer’s datasheet and include it in the final effective water–cement ratio and absolute-volume calculation. Do not subtract admixture water from 138 litres unless 138 litres has been defined as total mixing water.

M15 concrete mix design as per IS 10262:2019 showing a 100 mm target slump initial trial mix for mild-exposure plain concrete
M15 concrete mix design as per IS 10262:2019 for a 100 mm target slump—an initial trial mix for mild-exposure plain concrete.

Cementitious Content Calculation

The adopted cement content is:

Cement = 250 kg/m³

Cement Content Check Against the Maximum Water–Cement Ratio

For the selected mild-exposure plain-concrete condition, the reference maximum water–cement ratio is 0.60.

Cement required based on the maximum water–cement ratio:

Cement = Water ÷ Maximum permitted w/c ratio

Cement = 138 ÷ 0.60

Cement = 230 kg/m³

Therefore, 230 kg/m³ is required to satisfy the water–cement ratio limit for 138 litres of design water. The adopted 250 kg/m³ is above both the 200 kg/m³ durability minimum and the 230 kg/m³ water–cement ratio requirement.

The final cement content must be confirmed through approved trial-mix strength, workability and durability tests.

Using the adopted external design water:

Calculation-basis w/c = External design water ÷ Cement
Calculation-basis w/c = 138 ÷ 250
Calculation-basis w/c = 0.552

Therefore:

Calculation-basis w/c (external-water basis) ≈ 0.55

The cement content of 250 kg/m³ is selected as an initial trial value. It is above the minimum cement-content reference used for the selected plain-concrete condition, but the final value must be confirmed through strength, durability and workability trials.

Chemical Admixture Content

The superplasticizer dosage is taken as 0.60% by mass of cement.

Admixture quantity = 250 × 0.60 ÷ 100

Admixture quantity = 1.50 kg/m³

Therefore:

Superplasticizer = 1.50 kg/m³

The volume of liquid admixture is:

Volume of admixture = 1.50 ÷ (1.09 × 1000)

Volume of admixture = 0.00138 m³

The water contained in the liquid admixture must be checked separately against the final effective water–cement ratio. It is not included in the 138 litres/m³ external-water figure used in this illustrative calculation. The final approved mix must use the manufacturer’s datasheet and one consistent water-balance basis.

Coarse and Fine Aggregate Proportioning

For 20 mm nominal maximum-size aggregate and Zone II fine aggregate, the reference coarse-aggregate volume fraction at a water–cement ratio of 0.50 is approximately 0.62.

The selected water–cement ratio is approximately 0.55.

The increase from 0.50 to 0.55 requires an approximate reduction in coarse-aggregate fraction:

Adjustment = (0.55 − 0.50) ÷ 0.05 × 0.01

Adjustment = 0.01

Corrected coarse-aggregate fraction:

Coarse aggregate fraction = 0.62 − 0.01

Coarse aggregate fraction = 0.61

Fine-aggregate fraction:

Fine aggregate fraction = 1.00 − 0.61

Fine aggregate fraction = 0.39

The value of 0.61 is an initial proportioning value. The final aggregate blend must be confirmed by grading, workability and trial-mix results.

Absolute Volume Calculation

The absolute-volume method is used for one cubic metre of concrete.

Volume of Cement

Volume of cement = Mass ÷ (Specific gravity × 1000)

Volume of cement = 250 ÷ (3.15 × 1000)

Volume of cement = 0.0794 m³

Volume of Water

Volume of water = 138 ÷ (1.00 × 1000)

Volume of water = 0.1380 m³

Volume of Superplasticizer

Volume of admixture = 0.00138 m³

Volume of Entrapped Air

For normal non-air-entrained concrete with 20 mm aggregate:

Entrapped air = 1%

Volume of air = 0.010 m³

Volume Available for Aggregates

Volume of aggregates = 1 − (Volume of cement + Volume of water + Volume of admixture + Volume of air)

Volume of aggregates = 1 − (0.0794 + 0.1380 + 0.00138 + 0.010)

Volume of aggregates = 0.7712 m³

Coarse Aggregate Quantity

Volume of coarse aggregate = 0.7712 × 0.61

Volume of coarse aggregate = 0.4704 m³

Mass of coarse aggregate = 0.4704 × 2.70 × 1000

Mass of coarse aggregate ≈ 1,270 kg/m³

Fine Aggregate Quantity

Volume of fine aggregate = 0.7712 − 0.4704

Volume of fine aggregate = 0.3008 m³

Mass of fine aggregate = 0.3008 × 2.65 × 1000

Mass of fine aggregate ≈ 797 kg/m³

Final Initial Trial Mix

MaterialQuantity per m³
OPC 53 cement250 kg
Fine aggregate797 kg
Coarse aggregate1,270 kg
Adopted external design water138 litres
Superplasticizer1.50 kg
Calculation-basis water–cement ratio (external-water basis)Approximately 0.552
Target slump100 mm
Entrapped airApproximately 1%

The quantities are based on saturated surface-dry aggregate conditions.

Approximate Mass Ratio

Taking cement as one part:

Cement : Fine aggregate : Coarse aggregate

= 250 : 797 : 1270

= 1 : 3.19 : 5.08

This is a calculated mass-based trial proportion. It is not a fixed nominal mix ratio.

Approximate Coarse Aggregate Split

For an initial combined coarse aggregate blend:

Aggregate sizeApproximate percentageQuantity
20 mm aggregate60%762 kg
12.5 mm aggregate40%508 kg
Total coarse aggregate100%1,270 kg

The 60:40 split is only an initial trial proportion. The final blend must be selected according to actual sieve analysis and combined grading.

Quantities for a 50-Litre Trial Batch

A 50-litre trial batch is equal to:

0.05 m³

MaterialQuantity for 50 litres
OPC 53 cement12.50 kg
Fine aggregate39.85 kg
Coarse aggregate63.50 kg
Adopted external design water6.90 litres
Superplasticizer75 g

The plant water must be adjusted for aggregate moisture. The liquid admixture is added separately; its water contribution must be checked in the final effective water–cement ratio and absolute-volume calculation using the manufacturer’s datasheet.

Moisture and Absorption Correction

The calculated quantities are based on saturated surface-dry aggregate conditions.

Basis of the Illustrative Moisture Correction

For this simplified illustration, the stated free-surface-moisture percentages are expressed relative to the SSD aggregate masses. The calculation accounts only for free moisture above the SSD condition.

If the laboratory reports moisture on an oven-dry basis, or if an aggregate is below SSD condition, use the actual total moisture, absorption and SSD values in the approved batch correction. Do not use these example percentages directly for production batching.

Assume the following free surface moisture:

  • Fine aggregate = 3%
  • Coarse aggregate = 1%

Water Contributed by Fine Aggregate

Water = 797 × 0.03

Water = 23.91 litres

Water Contributed by Coarse Aggregate

Water = 1270 × 0.01

Water = 12.70 litres

Total Water Contributed by Aggregates

Total water = 23.91 + 12.70

Total water = 36.61 litres

Before considering water in the liquid admixture:

Water to be added = 138 − 36.61

Water to be added = 101.39 litres

Under the external-water basis used here, 101.39 litres is the plant water after subtracting the assumed aggregate free moisture. Do not deduct admixture water from this value unless the design is redefined on a total-water basis. For final approval, repeat the water–cement ratio and absolute-volume checks using the manufacturer’s datasheet.

Wet Fine Aggregate Quantity

Wet fine aggregate = 797 × 1.03

Wet fine aggregate ≈ 821 kg

Wet Coarse Aggregate Quantity

Wet coarse aggregate = 1270 × 1.01

Wet coarse aggregate ≈ 1,283 kg

The actual moisture and absorption values must be measured before batching.

Trial-Mix and Quality-Control Requirements

Before approving the mix for production, carry out laboratory and site trials using the actual materials.

Check the following:

  1. Slump immediately after mixing.
  2. Slump retention where delivery time is significant.
  3. Concrete temperature.
  4. Bleeding and segregation.
  5. Fresh concrete density and yield.
  6. Admixture compatibility and setting time.
  7. Aggregate moisture correction.
  8. Cube compressive strength at the specified ages.
  9. Workability and finishability.
  10. Batch-to-batch consistency.
  11. Compliance with project strength and durability requirements.
  12. Final approval by the responsible engineer.

Do not add unmeasured water at the site to correct slump. Workability adjustments should follow the approved admixture procedure and documented trial results.

15. Common Errors to Avoid

  • Treating 200 kg/m³ as the final cement content for every M15 mix.
  • Using M15 as a general reinforced-concrete grade.
  • Treating 30% water reduction as a fixed code value.
  • Ignoring water contained in liquid admixture.
  • Using SSD quantities directly without moisture correction.
  • Adding water at the site without recalculating the water–cement ratio.
  • Treating the ratio 1:3.19:5.08 as a volumetric nominal mix.
  • Using the same mix for pumping without a separate pump trial.
  • Changing M-sand to river sand without a new trial mix.
  • Using the calculated quantities without testing actual materials.

Frequently Asked Questions

Is this the final M15 concrete mix?

No. It is an initial trial mix based on the stated materials and assumptions. The final production mix requires laboratory and site verification.

Why is 250 kg/m³ cement used when the minimum is 200 kg/m³?

For the selected mild-exposure plain-concrete condition, 200 kg/m³ is the durability minimum. However, with 138 litres of design water and a maximum water–cement ratio of 0.60, at least 230 kg/m³ cement is required. Therefore, 250 kg/m³ is adopted as an initial trial value, subject to strength, workability and durability trials.

Can 250 kg/m³ cement achieve a 100 mm slump?

It may achieve the required slump when a compatible superplasticizer is used. The assumed 30% water reduction must be confirmed through an actual trial mix.

Can M15 concrete be used for RCC?

M15 should not be used as a general reinforced-concrete grade. The minimum RCC grade depends on the exposure condition and project requirements.

Is the ratio 1:3.19:5.08 a nominal mix ratio?

No. It is a calculated mass-based trial proportion. It is not the traditional volumetric nominal ratio of 1:2:4.

Can this mix be used for pumped concrete?

Not automatically. Pumped concrete requires separate checks for aggregate grading, paste volume, pumpability, slump retention and segregation resistance.

Can river sand be substituted for M-sand?

No direct substitution should be made. A change in fine aggregate requires new grading, moisture, absorption, workability and strength checks.

Why is the calculated water–cement ratio 0.552 instead of exactly 0.55?

The adopted water quantity is rounded to 138 litres:

138 ÷ 250 = 0.552

This is approximately equal to 0.55.

Can the cement quantity be reduced further?

It can be reduced only if the resulting mix satisfies the applicable minimum cement requirement, strength, durability and workability requirements through approved trials. Cement should not be reduced based only on the minimum value.

Related Resources

Conclusion

The preliminary M15 concrete mix per cubic metre is:

  • OPC 53 cement: 250 kg
  • Fine aggregate: 797 kg
  • Coarse aggregate: 1,270 kg
  • Adopted external design water: 138 litres
  • Superplasticiser: 1.50 kg
  • Calculation-basis water–cement ratio (external-water basis): approximately 0.552
  • Target slump: 100 mm
  • Approximate mass ratio: 1 : 3.19 : 5.08

These quantities are valid only for the stated materials, grading, specific gravities, moisture condition, admixture dosage and design assumptions.

Final approval requires trial-mix testing and confirmation by the responsible project engineer.

About T Square Civil Engineering

T Square Civil Engineering provides practical civil-engineering explanations, concrete technology guidance, construction calculations and site-oriented learning resources.

The content connects engineering theory with construction practice, testing, quality control and field application—from Theory to Construction Practice.

Disclaimer

The information on this website is provided for educational purposes only.

It does not replace project-specific engineering design, professional advice, approved drawings or construction specifications. Examples, calculations and suggested procedures should not be adopted directly for construction without appropriate verification. Always check the latest applicable standards and amendments, local requirements, project specifications, material-test results and site conditions.

Final design, testing, acceptance and construction decisions should be made by qualified professionals and the responsible project authorities.

T Square Civil Engineering is an independent educational platform and is not affiliated with the Bureau of Indian Standards, any government authority, cement manufacturer or admixture manufacturer mentioned on this page.

Leave a Reply

Your email address will not be published. Required fields are marked *